£112.50 / €124.88

Mini Titan Head and Tail deal as shown (not supplied with linkages) (tail gearbox not supplied with tail shaft you must use your existing tail shaft)
1 x E325 Head assembly
1 x E325 Tail Assembly
find out more

£39.99 / €44.39

Same Features as Plastic Case G401B but with metal case for added crash protection.
Comes with instructions
find out more

£22.00 / €24.42

Introduction:
Model helicopter building instructions always state pushrod length as measured from ball centre to ball centre.
Determining this dimension using conventional measuring tools is not really much more accurate than estimating the length.
Whole new design! Just like a vernier caliper. Very easy to use.
Precision CNC made
7075 hardness aluminum.
Fit for both left-handed and right-handed person.
IN STOCK
find out more

£120.00 / €133.20

Alien Command Advanced
CCPM Flight Stabilisation

More than just a flight stabilisation system...

•Full Alien Command CCPM flight stabilisation.
•120/140 degree swashplates.
•RC latency error reduction.
•Digital servo optimisation.
•CCPM geometry error correction.
•Flybarless system compatible.

How does it compare to other systems?:
Well it’s a lot cheaper, does a lot more, produces much smoother stabilisation and of course is a double edged sword because you can not only improve eCCPM but you can decide to use the stabilisation component or just switch off! Therefore once you are happy without the stabilisation components turn it off/remove it and just utilise all the other benefits to give yourself an exceptional smooth flight control.


Have we tried it?:
Of course we have set the unit using the software provided and it gives and incredible flight experience! Trex 450, 500 in 10mph + wind we could just leave the TX on the floor and leave at an altitude of 80+ meters with minimal drift – we were amazed.



RRP 123.49
find out more

£3.40 / €3.77

5 Minute Quality Epoxy Glue
Minute A/B Epoxy Glue.
A very high quality clear setting epoxy glue.
Excellent gap filling and bonding properties on almost all surfaces including delicate foam and hard to bond alloy.

Product comes in sealed air-tight packaging.
You wont find a better quality epoxy from China. In fact, its possible to find 20cent epoxy glues of the same size, however they dont dry clear and their holding strength and adhesion is very poor.
Our glue is produced by MIRA, one of Chinas leading glue manufacturers who supply glues to Chinas aerospace and civil engineering market, requiring strict quality and performance guidlines.
Save yourself the headache and only purchase quality glues.

An essential item for any building project and perfect for emergency in-field repairs
find out more

find out more

£199.99 / €221.99

Our New 500 size flybarless head comes as shown with an outrage Swashpalte fits most 500 Heli;s fits T Rex 500 SX 500 Lepton etc as shown

Supplied with Gaui GU365 stabi wroks great
find out more

£2.39 / €2.65

Gaui -Cable Tie with Touch Fastener 17cm( Set of 4 ) 910022
find out more

£235.90 / €261.85

Overview
Throw out your "1940’s-technology" mechanical flybar and replace it with a state of the art Digital Flybar. Rock solid hovering with a less complex, lighter rotorhead for more power or longer flight times!

The SK-360 Digital Flybar is a high performance, compact and lightweight electronic pitch and roll stabilizer for model helicopters of all sizes. Its function is to replace the traditional flybar (stabilizer bar) and its association linkages, boosting power, increasing flight times and reducing repair costs.

For 3D flying, dial up cyclic rates to the limit of blade stall, without losing any stability. This gives your heli lightning-quick 3D, with great performance in wind and a solid hover!

For Scale flying, cyclic rates can be dialed down for smooth, steady flight even in gusty wind. Both the look and the sound are more realistic. The SK360 flies great with 2, 3, 4, or 5 blades.

The SK-360 is a compact, single unit, and comes with a USB interface included. It weighs only 16 grams, and can be mounted upside-down, backwards, or rotated 90 degrees to fit in any heli.

The PC setup software lets you fully configure the swash mixing, servo motion, and stability. And, it's easy to upgrade the firmware at home so you'll benefit from any future product improvements with the click of your mouse. Plus, the setup software displays the precision PWM inputs and outputs, making it an excellent calibration tool for your servos and radio.

(Note: For nitro helis, the SK360 has now been tested up to 90 size)

Control Options:
· Adjustable Bell and Hiller ratio (direct vs. stabilized control)
· Adjustable roll (aileron) and pitch (elevator) rates
· Control feel is adjustable in-flight with optional Bank Switching & gain channel

Swashplate Options:
· Works with Digital or Analog servos
· Suitable for 120, 135/140, and 90 degree eCCPM, as well as mCCPM swashplates
· Swash Ring anti-binding algorithm
· Phase Trim adjustable to +-90°
· Swash servo-equalizing prevents uncommanded collective in aggressive maneuvers

High Performance:
· Synchronous, 12-bit precision (4096 step) PWM inputs from your radio
· Tightly grouped 12-bit servo PWM outputs for low swash motion error
· Super-accurate, crystal driven PWM timing
· Optional 125 Hz Digital servo frame rate
· Minimal lag (just a few milliseconds)
· Individually temperature compensated
· Wide input voltage range (up to 8.5 volts)
· Weight is only 16 grams

Package Contents:
· SK-360 Gyro unit
· Four receiver connection cables
· Four strips of 3M-4408tm mounting tape
· USB Interface with jumper
· USB Extension Cable
· CD with Interface Software

SK360 - Technical Specifications
Dimensions: 41 x 31 x 15 mm (1.6 x 1.2 x 0.6 in)
Weight (without cables): 16 grams (0.5 oz)
Operating Temp. Range: -5c to +45c
Operating Voltage: 3.6 to 8.5 VDC
Power Consumption: 28mA
Wiring Gauge: 22 or 24
Input Signals: 3-4 Channels (PWM 700-2300 us)
Servo Options: Analogue or Digital
Setup: USB interface, or by Transmitter Sticks
Field Gain Settings: Bell and Hiller Gain Dials, 0 - 100%
find out more

£79.00 / €87.69

Skookum LCD Field Terminal for the SK360
find out more

£110.00 / €122.10

This is the iMax B6 Quattro charger.
The iMax Quattro B6 allows you to plug 4 batteries into on charger simultaneously, and it will intelligently and automatically charge all 4 of them at once to their maximum capacity. To top of it, the batteries being charged do not even need to have the same configuration. You can connect different chemistry (ni-mh/Ni-Cd/LiPo/LiFe) batteries into any of the charging ports.

Input: DC 11 to 15V
Power source: 12V DC (car battery)/ AC mains PSU (>200Watts0
Charger power: 50Watts, current is regulated accordingly.
Discharger power: 5 watts, current is regulated accordingly
Cell count: 1-15 Nicd/NiMH cells; 1-6S LiPo/Lilon/LiFe cells; 1-10 Lead-Acide cells (2V to 20V)
Current drain for balancing Lithoum: 300mA
Charge termination: automatic, negative delta peak method for NiCd/NiMh; and automatic, voltage-dependent, CC-CV process
Dimensions: 225.4 x 158.6 x 62.4mm
Net weight: 1.09kg

Includes:
1 x charger
1 x pair alligator clips for Pb battery
1 x alligator to bullet connector cable
1 x JST to bullet connector cable
1 x Futaba to bullet connector cable
1 x Tamiya to bullet connector cable
1 x bullet connector with wire
1 x TP/FP adaptor
1 x XH adaptor
1 x instruction manual

In stock around 25-03-10 pre order
find out more

£135.00 / €149.85

This is a multi blades rotor head special for the scale helicopter It design no swash-plate lock (follower) require .The total hight of the centre hub only 35mm ,It make your model great scale look and C/G lower for sport preformance .
Fits 500 size Helicopters for that great Scale look
Try pairing with the Gyrobot 700 Stabiliser


find out more

£199.99 / €221.99

Our New 500 size flybarless head comes as shown with an outrage Swashpalte fits most 500 Heli;s fits T Rex 500 SX 500 Lepton etc as shown

Supplied with Gaui GU365 stabi wroks great
find out more

£13.75 / €15.26

Stainless gear puller -- for motor pinion/gear Removing
It is ok for motor shaft diameter 0.9-3.5mm
Back in stock now 11-03-10


find out more

£17.99 / €19.97

New March 2010 Sonix 325mm Carbon Fibre and white painted main Blades for 450 helicopters
Nice finishand well balanced right from the start
find out more

£3.20 / €3.55

This little tool will magnetize your scredriver heads in an instant. Great for inserting screws into those hard-to-reach places.
This item also demagnetizes items.
find out more

£12.00 / €13.32

Great Compact set of tools for your Dremel

Low cost and handy to use
find out more

£39.99 / €44.39

Same Features as Plastic Case G401B but with metal case for added crash protection.
Comes with instructions
find out more

£34.99 / €38.84

Selection of tools in attractive and practical tool box. Branded under the Helivol logo.
Product Specification:

Includes:
Pitch Gauge
Wire Cutters
Pliers
Ball Link Pliers
4.0mm Socket Driver
5.5mm Socket Driver
1.5mm Hex Driver x 2
2.0mm Hex Driver
2.5mm Hex Driver
Phillips Driver x 2
Flat Head Driver

find out more

£5.40 / €5.99

Turnigy 4mm Ball End Reamer
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.
find out more